Easy Contactor Replacement with SureSwitch!

December 25, 2024

In this tutorial, HVAC School's expert JD Kelly walks you through the step-by-step process of replacing a single pole contactor using the innovative SureSwitch.

What You’ll Learn:

Safety first: Proper power disconnection and access panel removal
How to identify contactor failure signs
Wire-for-wire replacement techniques
Mounting considerations and orientation tips
Wiring specifics for multi-volt control coils
Testing procedures for your new SureSwitch

Key SureSwitch Features Highlighted:

Sealed unit design
Dedicated mounting plate
Excellent wiring diagram
Multi-volt control coil compatibility
Enhanced reliability

Pro Tip: Always follow the manufacturer’s torque specifications and carefully review the wiring diagram before installation.

#contactor #contactor coil #hvac #sureswitch #white-rodgers

Comments

Most popular videos

See all +

Tips for Cleaning an Air Conditioning Common Drain

Gas Furnace Overview w/ AC Service Tech

Motor Overload and Safeties – Kalos Meeting

Don’t Overfill Refrigerant Recovery Cylinders The Easy Way

How to Replace an AC Condensing Fan Motor

How to Braze Air Conditioning Copper

How to Leak Test an AC With Nitrogen Pressure

How to Properly Pipe a Drain on a Fan Coil

4 Silly Mistakes of The Green HVAC Tech

How to Install an AC Disconnect

Why a Hard Shut Off TXV Closes

The Importance of SST (Evaporator Temperature) and Using a Scale (Kalos Meeting)

Adjusting Gas Pressure on a Standard and Gemini Furnace Valve

How a Heat Pump Reversing Valve Works

How and When to Use a Schrader Core Removal Tool

Why Does The Evaporator Coil Freeze (And How to Diagnose It)

How to Measure Total External Static Pressure (TESP)

Prevent this Common Manometer Mistake

Facts About Fusite (Compressor Electrical Pass Through Connections)

See Inside a Biflow/Heat Pump Filter Drier

Flammable Refrigerant Safety Basics – Kalos Meeting

How is 208 volts different than 230/240 volts?

Tips for Hiring & Getting Hired

How is a 3-Phase Motor Different than Single Phase

HVAC Class 11/24/2020 – Electrical Review

How to Measure Gas Pressure – Kalos Meeting

What is Common, Start and Run?

Perfect Flares Every Time w/ NAVAC NEF6LM

Ask Bryan Anything Live Call-in from 11/21/2020

How to Build a Sheet Metal Coil Case From Scratch

Basic Electrical Circuit Terms

The #1 Key to Service Success?

How To Keep Motors Running Cool And Efficient

Talk Through The Refrigerant Circuit Using The “Glass Tube” trainer

Top 10 HVAC Tech Tips for 100K

Installing a Rectangle to Round Transition into an Existing Metal Duct

How Humidity Impacts The Weight of Air

Testing Home Pressure Imbalance w/ Genry Garcia (Spanish)

Some of Bryan’s Favorite New Tools Giveaway Meeting

Bert Teaches The Basic Refrigerant Circuit + Safety

Setting a Refrigerant Charge by Subcool

Soft Skills Can Be Hard (Disciplines of Growth)

How to Fabricate a Metal Supply Plenum From Scratch

Delivered Capacity Basics – Kalos Meeting

Sequencer Facts – They Aren’t All The Same

Wire Routing & Float Switch Positioning

Dual Voltage and Part Start 3-Phase Motors

Apprentice Program Day 1 – Using Your Resources w/ Jason Obrzut

Bert Cleans Out His DIRTY Work Van (And You Should Too!) #BERTLIFE

Liquid Line VS. Discharge Line

Tips for Proper AC System Cleaning – Kalos Meeting

Motor Replacement Tips & Tricks – Kalos Meeting

Better Duct Installation Practices – Kalos Meeting

THIS Is How My FIRST WEEK As An HVAC Apprentice Went (I’m Being Trained By WHO?!)

How to Find Refrigerant Leaks – Kalos Meeting

Critical System Diagnosis for Residential HVAC

Diagnosing Open & Short Circuits

Installing a Mitsubishi One-Way Ceiling Cassette In An Unfinished Room (You Can See EVERYTHING!)

How to Use a Blower Door (Como usar el Blower Door)

How to Stop Drain Snot (Bacterial Zoogloea)

Symptoms of Low Evaporator Airflow

Preventing Flooding On a Walk-In Call

Diagnosing and Replacing a Run Capacitor

Symptoms of Low Refrigerant Charge

Preventing, Finding & Repairing Refrigerant Leaks

Proper Use of Manometers for HVAC Technicians

Tool Talk Live – Probes, Bags, Hand Tools, Power Tools & More

Cleaning BARD units with Venom Packs

Electrical Basic Concepts – RSES NATE Prep

Selling, Upselling, IAQ , Hardstart Kits and More

Cutting & Installing a Rectangle Duct Connection

How to Make a Leak Free Canvas Duct Connector

Cooling Commissioning Measurements Walk Through w/ MeasureQuick

How to Checkout Blower Settings Using a Manometer

Recovery Best Practices & Giveaway

Introduction to the Fieldpiece Joblink Manometer Set

HVAC SCHOOL MONEY TALK – Don’t Make This Common Mistake

Testing out a High Performance HVAC Installation

Commercial Refrigerant Retrofit Options in a Crisis Economy #LIVE

HVAC Myth Busting #2 – Volts Go Down, Amps Go Up

Rectorseal RSH 50 Installation

Setting Up Residential Demand Ventilation with Laser Egg

DUCTLESS Control and Humidity Hack with Cielo Breez

Rectorseal Surge Protector Installation

HVAC Contractors Guide to COVID-19

DIY Cloth Mask with HEPA Pocket

How to Make an Indoor Air Cleaner the Cheap and Easy Way

Electrical Diagnostic Thinking

Human Comfort Basics – RSES NATE Prep

5 Install Mistakes that Kill Systems

UV Part 2 – Honest UV Facts from a Manufacturer

UVC Air Purification – Live Podcast Part #1

How to Make a Metal Duct Transition in the Field

Reversing Valves (RSES NATE Prep)

Sunday Coil Cleaning #BERTLIFE

Liquid Line Solenoid on Long Refrigerant Lines

Condensing Unit Install Practices (RSES NATE Prep)

HVAC Motor Types (RSES NATE Prep)

Relative Humidity in the Supply Air Stream

Advanced Combustion Analysis (HVAC) w/ Jim Bergmann

Advanced MeasureQuick Diagnosis w/ Jim Bergmann

How to Flow Nitrogen While Brazing

Compressor Tear Down (Don Gillis / Trevor Matthews)

Compressor Facts and Troubleshooting (Don Gillis / Trevor Matthews)

Nikki Krueger – The Dripping Point

Troubleshoot a Grounded (Shorted to Ground) Compressor

Using Power Factor to Check Capacitors Under Load

Straight Cool Air Conditioning Schematic (Carrier)

Charging During Low Outdoor Ambient w/ Charging Jacket

Recovery Machine Speed Race 🏁NAVAC NRDD Digital vs. Appion G5 Twin

Is There Mold in my Ducks! 🦆(Ducts)

A thermostat miswire and distracted diagnosis #BERTLIFE

Cleaning large coils with CoilPro

Inductive Reactance in Real Life

50K Subscriber Special & Behind the Scenes Tour

Compressor Won’t Run Diagnosis

A Blower and Heat Strip Dangerous Mistake

How to adjust a TXV, TEV or TX Valve

5 HVAC/R Terms That Sound Worse Than They Are

Fieldpiece Joblink Firmware Update Demo

Check out our most recent video

How to Evacuate an AC system, Full Vacuum Procedure

Our latest Podcast

HVAC School – For Techs, By Techs

Real training for HVAC ( Heating, Ventilation, Air Conditioning and Refrigeration) Technicians. Including recorded tech training, interviews, diagnostics and general conversations about the trade.

In today’s podcast, Bryan talks with legendary Hydronics author and trainer Dan Holohan about the history of steam heating and some practical applications of old ideas. Recently, Dan has been working on more novels, having published two of them over the past few months.

Steam heating is a “lost art” nowadays; it has become increasingly uncommon and has been disappearing since the Vietnam War. Many people who understood steam heating either retired or died after the Vietnam War. Many elements of steam heating are difficult to understand or surprising. (For example, steam pressure has a surprising relationship with velocity: low-pressure steam moves through piping much more quickly than high-pressure steam.) So, Dan Holohan is on a mission to revive that knowledge and teach the newer generations about the lost art.

There are many older steam heating systems still operating today, especially in the older large buildings in New York. Dan learned a lot about steam heating when working on these old systems and optimizing them. Most of the time, he optimized those systems by removing unnecessary accessories, not by adding components like steam traps.

Many old boilers used coal as a heat source. Nowadays, many old boilers have been fitted with conversion oil burners with thermostats, but they are still piped for coal. Some systems now have multiple risers or massive vents on the main riser to prevent the thermostats from getting too hot too early and satisfying the thermostat too early. We call that master venting, which reduces pressure and allows steam to move very quickly and efficiently.

Dan also discusses:

The 2-PSI standard
Transportation metaphors for BTUs in steam
Harmful renovations for old boilers
Replacement vs. restoration mindsets
Gaps in steam boiler education
Monopolizing the market if you HAVE the education
Boiler piping and venting
Two-pipe vs one-pipe steam

Find out more about Dan and hydronic heating at HeatingHelp.com.

Have a question that you want us to answer on the podcast? Submit your questions at https://www.speakpipe.com/hvacschool.

Purchase your tickets or learn more about the 6th Annual HVACR Training Symposium at https://hvacrschool.com/symposium. Subscribe to our podcast on your iPhone or Android. Subscribe to our YouTube channel. Check out our handy calculators here or on the HVAC School Mobile App for Apple and Android.

Search Episodes

Redux – The Lost Art of Steam Heating w/ Dan Holohan

12/26/2024

Bryan Orr

Q&A on Superheat – Short #223

12/24/2024

Bryan Orr

Duct Cleaning – How Long & How Often?

12/19/2024

Bryan Orr

Are EVs an Opportunity? – Short #222

12/17/2024

Bryan Orr

Choosing HVAC Cleaners w/ Becca from Viper

12/12/2024

Bryan Orr

Q&A – Evap Placement – Short #221

12/10/2024

Bryan Orr

Can Ducts Be Cleaned Ethically?

12/05/2024

Bryan Orr

Should I Fog or “Sanitize” My Ducts? – Short #220

12/03/2024

Bryan Orr

Condensing Furnace Drain Guidance w/ AC Service Tech

11/28/2024

Bryan Orr

What Can Be Done About Healthcare? w/ Ethos

11/26/2024

Bryan Orr

Search Results placeholder

Easy Contactor Replacement with SureSwitch!

Subscribe to our Youtube channel