Some Refrigeration Thoughts for A/C Techs

By November 17, 2016

Some Refrigeration Thoughts for A/C Techs

In this episode I talk to Jeremy Smith and he shares some of his refrigeration experience… and his Barry White smooth voice.

Also – got to hvacrschool.com/10K to participate in Stephen Rardon's awesome tool giveaway.

Check out our most recent video

How to Evacuate an AC system, Full Vacuum Procedure

Our latest Podcast

HVAC School – For Techs, By Techs

Real training for HVAC ( Heating, Ventilation, Air Conditioning and Refrigeration) Technicians. Including recorded tech training, interviews, diagnostics and general conversations about the trade.

In this short podcast episode, Bryan talks about locked compressors and hard starts. He explains what actually happens when a compressor locks and covers when and how to use hard starts appropriately.

Locked compressors are compressors that trip on overload during startup; they’re considered “locked” because the rotor doesn’t turn inside the stator and generates heat instead. The overload opens, but the compressor shell typically does not heat up very much when the overload opens.

When you have a locked compressor, you need to start investigating the root cause with a thorough visual inspection. Then, check the run capacitor. A hard start kit helps you get the equipment working, but we should make sure we’ve addressed underlying electrical issues or installation conditions before installing a hard start kit. If the unit is old, then we may use a hard start as a temporary solution until the customer can purchase a new unit. In any case, it’s best to use a factory hard start if the system requires it, but it’s okay to use an aftermarket hard start kit to get an old system to run.

Hard start kits consist of a start capacitor in series with the start winding, which moves more current into the start winding and decreases the time it takes to start the compressor; lower current readings indicate a faster amperage drop, as most ammeters read timed average values. The potential relay needs to open to take the start capacitor out of the circuit so that we don’t continuously apply additional current to the start winding, which hurts the compressor over time. The hard start kit is not a silver bullet that solves all problems, and we need to know when to use them and how to use them appropriately.

Learn more about the 5th Annual HVACR Training Symposium at https://hvacrschool.com/Symposium24.

If you have an iPhone, subscribe to the podcast HERE, and if you have an Android phone, subscribe HERE.

Check out our handy calculators HERE.

Search Episodes

Locked Compressors and Hard Starts – Short #175

10/03/2023

Bryan Orr

Residential Exhaust Codes and Best Practices

09/28/2023

Bryan Orr

Wiring Refrigerated Cases w/ Nathan & Phil

09/14/2023

Bryan Orr

Things to Keep out of the System – Class

09/07/2023

Bryan Orr

ACH (Air Changes Per Hour) – Short #174

09/05/2023

Bryan Orr

Oil Return and Refrigerant Charge in VRV w/ Roman Baugh

08/31/2023

Bryan Orr

Magical Air Cleaning Oxides? – Short #173

08/29/2023

Bryan Orr

Can Filters Capture Viruses? – Short #172

08/22/2023

Bryan Orr

Heat Pumps + Inverters w/ Joey H

08/17/2023

Bryan Orr

Get Air Where it Needs to Go W/ Joey H.

08/10/2023

Bryan Orr

Search Results placeholder

Comments

Related Tech Tips

Oxyacetylene Torches: Tips and Operation

Everyone in the HVAC/R trade uses some type of torch to braze or solder alloys together. So, what is the proper way to handle an oxyacetylene torch? It turns out that there’s more than one right answer. Depending on which torch rig you use, the manufacturer’s manuals for operation may vary. Everyone (hopefully) knows […]

Floating Suction and Head Pressure

This article was inspired by a podcast episode featuring Jeremy Smith. Jeremy is a refrigeration mechanic and has contributed a lot of good material to HVAC School. You can listen to that podcast on floating suction and head HERE. Those of you who drive your own vans are probably all too familiar with the following […]

Plenum Takeoffs Best Practices

In my second year in HVAC, I went out with a senior technician to install a supply duct for a bathroom in a house. While he ran the duct, I cut a hole in the plenum and attached the collar. He crawled back across the attic and very nicely told me that people don’t typically […]

More tech tips