Dylan myrick Basic Refrigerant Circuit Course June 5, 2022, 9:00 pm

By June 6, 2022

Dylan myrick Basic Refrigerant Circuit Course June 5, 2022, 9:00 pm

Check out our most recent video

How to Evacuate an AC system, Full Vacuum Procedure

Our latest Podcast

HVAC School – For Techs, By Techs

Real training for HVAC ( Heating, Ventilation, Air Conditioning and Refrigeration) Technicians. Including recorded tech training, interviews, diagnostics and general conversations about the trade.

Dr. Allison Bailes from Energy Vanguard joins the podcast to answer the age-old question: do houses need to breathe? He also talks about his new book, A House Needs to Breathe… Or Does It? You can purchase that book directly through the Energy Vanguard site at https://energyvanguardstore.com/ or on Amazon.

HVAC professionals can benefit from learning about building science because there is a lot of overlap between the two, and an HVAC technician who knows about building science can set themselves apart in the market.

In short, Dr. Bailes doesn’t think a house needs to “breathe,” especially if a house brings in low-quality air, especially humid air, through gaps and cracks. Some people also use the term “breathe” differently; some may be referring to leakiness, and others may refer to drying out a house. It is necessary for a house to be dry, but we want to make sure that fresh air is controlled.

If you build a home tightly, you have to ventilate it correctly. We have to control air, liquid water, water vapor, and heat. Heat is especially complicated, as it has three different ways of moving and can come in sensitive and latent varieties. One way of controlling those is through control layers like vapor barriers, though these aren’t always needed; we must understand the vapor flow to determine if a vapor barrier is necessary.

Dr. Bailes and Bryan also discuss:

Energy Vanguard’s resources
The chapters of “A House Needs to Breathe… Or Does It?”
IAQ – filtration, humidity control, ventilation, and source control
Challenges with attic air
Dr. Bailes’s book-writing process
The HVACR Training Symposium and other events w/ Dr. Bailes

Keep up with Energy Vanguard, read the blog, and subscribe to the weekly newsletter at https://www.energyvanguard.com/.

If you have an iPhone, subscribe to the podcast HERE, and if you have an Android phone, subscribe HERE.

Check out our handy calculators HERE.

Search Episodes

Do Houses Need to Breathe? w/ Allison Bailes

01/26/2023

Bryan Orr

What the Heck is High Performance HVAC w/ David Holt

01/19/2023

Bryan Orr

Setting Realistic Customer Expectations w/ Ed Janowiak

01/12/2023

Bryan Orr

Mini Split Install and Service Tips

01/03/2023

Bryan Orr

CO Doesn't Leak w/ David Richardson

12/29/2022

Bryan Orr

One HSI Furnace Control to Rule Them All w/ Jim Fultz

12/27/2022

Bryan Orr

Using Ice to Balance Energy Consumption

12/22/2022

Bryan Orr

We need to Pay Better! – An Audio Manifesto

12/20/2022

Bryan Orr

Refrigerant Myth Busting w/ Dr. Chuck

12/15/2022

Bryan Orr

The Good, Bad and Ugly of Trade Schools

12/13/2022

Bryan Orr

Search Results placeholder

Related Tech Tips

What Should My Subcooling Be?

This is the article you read BEFORE you call and ask a senior tech what your subcool should be. It's also the one you send to a junior tech when they call and ask you: So, what is subcooling? (Or subcool, as many call it.) Subcooling is a measurement of temperature DECREASE of a […]

20° ΔT (Delta T), A Lazy Rule of Thumb

What should the delta T (ΔT) be? What do you mean!? 20 degrees, of course! We are referring to the air temperature drop across an air handling unit or evaporator coil in cooling mode. Actually, depending on who you ask, the answer will range between 18-22 degrees Fahrenheit. Heck, I’ve heard some insist that […]

It Has a Flat For a Reason

When tightening down a blower wheel or a fan blade on a motor shaft, ONLY tighten it on the flat of the shaft. If you have more than one screw but only one flat surface on the shaft, only tighten the one set screw. Also… Refrain from over-tightening set screws; they need to bite into […]

More tech tips