Prevent Compressor Murder Part 2 w/ Emerson

By April 24, 2018

Prevent Compressor Murder Part 2 w/ Emerson

Part 2 of the discussion with Trevor Matthews with Emerson about causes of air conditioning and refrigeration compressor failure and the causes Verifying System Operation Sheet from Emerson https://hvacrschool.com/EmersonVerify Diagnosing Compressor Failures from Emerson https://hvacrschool.com/CompFailuresWe talk with Trevor Matthews with Emerson about causes of air conditioning and refrigeration compressor failure and the causes Verifying System Operation Sheet from Emerson https://hvacrschool.com/EmersonVerify Diagnosing Compressor Failures from Emerson https://hvacrschool.com/CompFailures

Check out our most recent video

Locked Compressors

Our latest Podcast

HVAC School – For Techs, By Techs

Real training for HVAC ( Heating, Ventilation, Air Conditioning and Refrigeration) Technicians. Including recorded tech training, interviews, diagnostics and general conversations about the trade.

In this short podcast, Bryan debunks the myth that electricity only takes the path of least resistance.

It is true that more current will typically take paths of lower resistance; it’s much easier for more electrons to flow through a path with lower resistance, which is consistent with Ohm’s law. Ohm’s law states that a circuit will have higher current with you have lower resistance so long as the voltage stays the same.

In most cases, the voltage stays relatively constant; transformers don’t often need to limit their currents, so there usually isn’t a voltage drop. When power supplies are regulated, the voltage is usually fixed, not the amperage. As a result, dropping the resistance in a circuit will increase the current.

Ohm’s law holds true for both resistive and inductive loads. Inductive loads, however, are a bit tricky because the resistance isn’t constant. As motors spin faster, they create back EMF or impedance, which is magnetic resistance. The resistance only shows up once a motor, solenoid, or another electromagnetic component is energized; the resistance is much more dynamic.

An electrical current takes ALL parallel paths, not just the path of least resistance. The current also stays proportional to the resistance, even when it takes paths of many different resistance values. Our bodies are also parallel paths, so there’s a risk of electric shock even though our bodies usually have much higher resistance than loads. Wet skin has less resistance than dry skin, so that’s why electricity and water are so dangerous to us; lower resistance means that more current can flow through our bodies.

If electricity ONLY took the path of least resistance, we wouldn’t be able to operate all the appliances and electrical components in our homes. The only prerequisite is an electrical potential (voltage).

If you have an iPhone, subscribe to the podcast HERE, and if you have an Android phone, subscribe HERE.

Check out our handy calculators HERE.

Search Episodes

Myth: Path of Least Resistance – Short #154

10/04/2022

Bryan Orr

Dehumidification in Shoulder Seasons w/ Nikki

09/29/2022

Bryan Orr

Time Management – Short #153

09/27/2022

Bryan Orr

Become a Better Mentor w/ Eric Kaiser

09/22/2022

Bryan Orr

HVAC Measurement Types and Benefits

09/15/2022

Bryan Orr

Ventilation and 62.2 Intro & Rant w/ Genry Garcia

09/08/2022

Bryan Orr

Pressure Enthalpy without Tears

09/01/2022

Bryan Orr

Total Heat of Rejection – Short #152

08/30/2022

Bryan Orr

Hard Start vs. Easy Start

08/25/2022

Bryan Orr

Heat of Compression – Short #151

08/23/2022

Bryan Orr

Search Results placeholder

Related Tech Tips

Ball Bearing vs. Sleeve Bearing Motors

One aspect of motor selection that can get overlooked is motor bearings, and it can have big consequences. Sleeve bearings are most common in residential and light commercial applications because they are less expensive and quieter. They don't have rolling “balls” but rather rely on a thin film of oil on metal sleeves. Sleeve bearings […]

Mistakes in Measuring Ohms

In HVAC and electrical school, one of the first things you learn about electricity is Ohm's law: Volts (V) = Amps (I) x Ohms (R) Pretty simple, right? Watt's law is just as easy: Watts (P) = Volts (E) x Amps (I) With this newfound knowledge, the student walks confidently into the real world with […]

Flaring Copper: Best Practices

Technicians have to make flare fittings in the field every day. Most of the time, the application is for mini-split/ductless installs. However, you may encounter certain situations where flared fittings are more practical than a braze joint. Regardless of the reason, flared connections are notorious in our trade for being popular leak areas. Either the flare […]

More tech tips