3D Duct Modeling For Residential

Russ King joins us to discuss simplifying duct design for residential contractors. We focus on using 3D software for duct modeling.

While computers are great tools for duct design, you must be careful with them. Computer technology doesn't correct your mistakes; it allows you to make mistakes more quickly. Russ made 3D software specifically for duct modeling, and its goal is to help technicians/contractors with duct designs and equipment sizing. The software is good for quick duct design, can determine flex duct design, and is ideal for broad usage in residential HVAC.

Russ has noticed that existing energy modeling and load calculation software ask for extremely specific inputs, which can confuse technicians. He was frustrated with the process and wanted to make software that could help technicians solve the problems that mattered in a way that made sense. With the help of his son, Russ came up with Kwik Model (of Coded Energy). They developed software that allows users to design ducts and adjust parameters easily. The goal is for Coded Energy to be a simple, straightforward duct design software that addresses the hardest duct design issue: making the ducts fit.

Coded Energy is written in Unity, which is used for video games and architecture/automotive design. The user essentially imports a floor plan, scales it, places boxes, and stretches the boxes to meet the design conditions. Once the user has built the house, the software can calculate the surface area automatically. Then, the user can use EnergyGauge for load calculations and equipment selection. The user can then draw ducts and have the software size the ducts for them.

Russ and Bryan also discuss:

Equipment selection for latent removal capacity
Oversizing issues
Designing ducts for building plans
Comfort diagnostics
2D vs 3D modeling
Getting feedback in the field post-design

Visit kwikmodel.com to learn more.

Learn more about Refrigeration Technologies HERE.

If you have an iPhone, subscribe to the podcast HERE, and if you have an Android phone, subscribe HERE

Comments

Q&A on Superheat – Short #223

Duct Cleaning – How Long & How Often?

Are EVs an Opportunity? – Short #222

Choosing HVAC Cleaners w/ Becca from Viper

Q&A – Evap Placement – Short #221

Can Ducts Be Cleaned Ethically?

Should I Fog or “Sanitize” My Ducts? – Short #220

Condensing Furnace Drain Guidance w/ AC Service Tech

What Can Be Done About Healthcare? w/ Ethos

How to Predict Air Flow Issues in the Sales Process

Author:

Bryan Orr

Company: HVAC School

Position: Founder

Russ King

Company: Coded Energy, Inc

Position: Founder and CEO

Check out our most recent video

How to Evacuate an AC system, Full Vacuum Procedure

Our latest Podcast

HVAC School – For Techs, By Techs

Real training for HVAC ( Heating, Ventilation, Air Conditioning and Refrigeration) Technicians. Including recorded tech training, interviews, diagnostics and general conversations about the trade.

In this short Q&A podcast episode, Bryan answers a listener-submitted question about superheat, including what it is and how we measure it.

Superheat is the number of degrees a refrigerant is above its saturation point. The saturation point is where you will have a liquid-vapor mix, so superheat only exists when a substance is a vapor. Saturated refrigerant should only exist in the evaporator and condenser, during which it is being boiled or condensed.

We usually measure superheat at the evaporator coil outlet and compressor inlet. The superheat at the evaporator outlet is usually around 5-14 degrees Fahrenheit, and it’s often between 10 and 20 degrees at the compressor inlet (compressor superheat). However, many systems try to get lower superheat values, and some manufacturers may require higher superheat values at the compressor inlet to prevent liquid refrigerant from getting into the compressor. Accumulators can help keep liquid refrigerant out of the system as well. We may also measure superheat coming out of the compressor on the discharge line (discharge superheat); this superheat may exceed 100 degrees Fahrenheit. Discharge superheat can let you know if the compressor is overheating the oil and causing breakdown or carbonization.

We use superheat to set the charge for fixed-orifice metering devices (as opposed to subcooling for TXVs), as superheat is a measure of how well we’re feeding our evaporator coil. When the system is off, the superheat will be 0. A system will equalize, and the refrigerant will be at saturation when that happens.

Have a question that you want us to answer on the podcast? Submit your questions at https://www.speakpipe.com/hvacschool.

Purchase your tickets or learn more about the 6th Annual HVACR Training Symposium at https://hvacrschool.com/symposium. Subscribe to our podcast on your iPhone or Android. Subscribe to our YouTube channel. Check out our handy calculators here or on the HVAC School Mobile App for Apple and Android.